Call 000 000 0000

No Hot Water? A Safe Checklist Before You Call

A Fullerton homeowner guide, with official sources.

Call now 000 000 0000Placeholder number while the live line is set up.
  • Calls only, no forms
  • Ask if your address is covered
  • Tank, tankless, gas, electric, heat pump
Illustration for the Fullerton guide: No Hot Water? A Safe Checklist Before You Call
Illustration

Last updated

If you have no hot water, start with the simple things: is it every faucet or just one, is the gas or power on, and is the heater showing any light, code or flame? Many no-hot-water calls turn out to be a pilot that went out, a tripped breaker or a tankless unit waiting on a reset. If you smell gas at any point, stop, leave the house and call SoCalGas or 911 from outside.

Step 1: Every faucet or just one?

If only one faucet or shower is cold, the problem is probably at that fixture: a mixing valve, a cartridge, or a single-handle faucet's anti-scald limit. If every hot tap is cold, the problem is at the heater.

Step 2: Gas tank heaters

  1. Check that the gas valve on the supply line is open (handle parallel to the pipe).
  2. Look through the sight glass near the bottom of the heater. Older heaters have a standing pilot flame. Many newer heaters use electronic ignition.
  3. If the pilot is out and you don't smell gas, follow the relighting steps on the heater's label exactly.
  4. If the pilot won't stay lit after a careful try or two, stop. A worn thermocouple, a dirty pilot or a clogged air intake screen is likely. See why a pilot keeps going out.
  5. Check whether other gas appliances work. If none do, the problem may be the gas supply. Contact SoCalGas.

Not sure what your water heater needs? Talk it through by phone.

Call 000 000 0000

Step 3: Electric tank heaters

  1. Check the breaker panel for a tripped double-pole breaker. Switch it fully off, then on, once.
  2. If it trips again, leave it off. That points to a short in an element or wiring.
  3. If the breaker holds and you still get no heat after an hour or so, the high-limit reset may have tripped or an element may have failed. The reset sits behind a panel next to live 240-volt terminals, so it's safer to call. See electric water heater repair.

Step 4: Tankless heaters

  1. Look at the display for an error code and write it down.
  2. Confirm the unit has power. A tripped GFCI outlet or breaker will shut it down even though it runs on gas.
  3. Make sure the gas valve is open, and try a hot tap at a good flow rate, since a trickle may not trigger the burner.
  4. If the code returns, check the manual or the manufacturer's website. Don't keep resetting repeatedly. See tankless repair.

Step 5: Look for leaks and damage

While you're at the heater, look for water on the floor, rust at the base, scorch marks around the burner door or soot near the vent. Any of these change the job from a quick fix to a repair or replacement decision. If water is spreading, shut the cold supply valve on top of the heater. See leaking water heater help.

When to stop and call

  • You smell gas (leave first and call SoCalGas or 911 from outside).
  • The breaker trips again after one reset.
  • The pilot won't stay lit, or the burner flame is yellow and sooty.
  • There's water under the tank, or rust and scorch marks.
  • A tankless code keeps coming back.

What to have ready

Have the heater type (gas, electric, tankless or heat pump), the size and age from the label, any error codes, what you've already tried and your address or cross streets in Fullerton. That makes the call quicker and helps the provider bring the right parts.

Talking it through by phone

If you'd rather have someone look at it, call the number on this page. Mention what you've already checked, the heater's type and age from the label and your address or nearest cross streets in Fullerton or a nearby city. Coverage, timing and pricing are confirmed on the call with the provider, not promised in advance by this site.

Sources

Checked on November 13, 2026. Rules and programs change, so confirm anything important with the agency.

Quick answers

Why do I have hot water in the morning but not at night?

That usually means the heater can't keep up with demand. It could be undersized for the household, a failed lower element on an electric tank, heavy sediment taking up space in a gas tank, or a dip tube that's broken and mixing cold water into the hot. A service visit can sort out which.

How long should a water heater take to recover?

It depends on size and fuel. Gas tanks generally recover faster than standard electric tanks, and heat pump units in efficiency mode recover more slowly still. If recovery has gotten noticeably slower than it used to be, sediment or a failing part is a likely cause.

Hot water problem in Fullerton, CA?

One call. Ask whether your address is covered and what the next step is. Call to check availability.

Call 000 000 0000
Water heater trouble in Fullerton?Call 000 000 0000